[Previous][Next]
DTC P0720: Malfunction of Output Speed Sensor
 
 
 
 
DIAGNOSTIC FUNCTION
The TCM determines whether the system is defective by monitoring the output speed sensor.
 
 
DESCRIPTIONS OF MONITOR METHODS
  • The status with the secondary pulley speed of 1,500 r/min or more and with the output shaft speed of 150 r/min or less continues for 10 seconds.
  • When the output shaft speed has dropped abruptly from 730 r/min or more to 90 r/min or less, and then it keeps 90 r/min or less for 0.5 seconds continuously.
 
 
MONITOR EXECUTION
  • Transmission range: D, R or B
 
 
MONITOR EXECUTION CONDITIONS (OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
  • P0705: Malfunction of transmission range switch
  • P0791: Malfunction of secondary pulley speed sensor
Sensor (The sensor below is determined to be normal)
  • Transmission range switch
  • Secondary pulley speed sensor
 
 
LOGIC FLOW CHARTS [Monitor Sequence-Input Rationality Low (Open/Low revolution)]
 
 
LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
 
 
DTC SET CONDITIONS
Check Conditions
  • Transmission range switch position: D, R or B.
  • Voltage of battery: 10 volts or more.
  • Voltage of battery: 16.5 volts or less.
Judgment Criteria
  • The status with the secondary pulley speed of 1,500 r/min or more and with the output shaft speed of less than 150 r/min continues for 10 seconds.
  • The output speed has dropped abruptly from 730 r/min or more to 90 r/min or less. Then at least 0.5 seconds have passed with the reduced speed.
 
 
OBD-II DRIVE CYCLE PATTERN
The vehicle is driven for at least 20 seconds with the engine speed at 3,500 r/min or more.
 
 
PROBABLE CAUSES
  • Malfunction of output speed sensor
  • Damaged wiring harness and connectors
  • Malfunction of TCM
 
 
DIAGNOSIS
STEP 1. Check the following connector
  • Output speed sensor connector
Check the terminals for a contact status problem and internal short circuit.
Is the check result normal?
Go to Step 2.
Repair the defective connector.
 
STEP 2. Check for open circuit in SGN2 line between the output speed sensor connector and the TCM connector
Is the check result normal?
Go to Step 3.
Repair the connector(s) or the wiring harness.
 
STEP 3. Voltage measurement at output speed sensor connector (terminal No. 1)
(1) Disconnect the output speed sensor connector, and measure at the wiring harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between the output speed sensor connector (terminal No. 1) and body ground.
OK: 10 V or more
Is the check result normal?
Go to Step 4.
Repair the connector(s) or the wiring harness (power supply line between the output speed sensor connector terminal No. 1 and the J/B connector).
 
STEP 4. Check the following connector
  • TCM connector
Check the terminals for a contact status problem and internal short circuit.
Is the check result normal?
Go to Step 5.
Repair the defective connector.
 
STEP 5. Check for open circuit or short to ground in OUTS line between the output speed sensor connector and the TCM connector
Is the check result normal?
Go to Step 6.
Repair the wiring harness.
 
STEP 6. Measure the output wave pattern of the output speed sensor at TCM connector (OUTS terminal).
(1) Connect the output speed sensor connector and TCM connector.
(2) Selector lever position: D range.
(3) Drive at a constant speed of approx. 20 km/h.
(4) Connect an oscilloscope, and measure the voltage between TCM connector OUTS terminal and body ground.
OK: A wave pattern such as the one shown on (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 11 V or more and the minimum value should be 1 V or less. There should be no noise in the output wave pattern.
Is the check result normal?
Go to Step 7.
Replace the output speed sensor.
 
STEP 7. Symptom recheck after erasing diagnostic trouble code
Is the diagnostic trouble code stored?
Replace the TCM.
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunctions .).