[Previous][Next]
REMOVAL AND INSTALLATION
 
 
Removal steps
1.Breather hose
2.PCV hose
3.PCV valve
4.PCV valve gasket
5.Oil filler cap
6.O-ring
7.Oil drain plug
8.Oil drain plug gasket
<<A>>>>I<<9.Oil filter
<<B>>>>H<<10.Oil filter stud
>>G<<11.Oil filter cover
>>F<<12.Cylinder head cover
13.Cylinder head cover gasket
14.Transaxle stay
<<C>>>>E<<15.Oil pan
16.Oil strainer
17.Oil strainer gasket
>>D<<18.Water pump
>>D<<19.O-ring
>>C<<20.Timing chain case
>>B<<21.Timing chain case cover
>>A<<22.Front oil seal
23.O-ring
 
 
REMOVAL SERVICE POINTS
 
 
<<A>> OIL FILTER REMOVAL
Use special tool oil filter wrench (MB991396, MB991828) or commercially-available tool to remove the oil filter.
 

 
 
<<B>> OIL FILTER STUD REMOVAL
Remove the oil filter stud using recommended tool screw extractor (MB992684) or equivalent.
noteThis recommended tool is a component of screw extractor set (MB992678).
 

 
 
<<C>> OIL PAN REMOVAL
1. Remove the oil pan mounting bolts.
2. Lightly tap special tool oil pan FIPG cutter (MD998727) between the oil pan and the cylinder block.
3. Lightly tap and slide special tool to remove the oil pan.
 
 
 
 
INSTALLATION SERVICE POINTS
 
 
>>A<< FRONT OIL SEAL INSTALLATION
cautionWhen installing the front oil seal, be careful to avoid damage to the front oil seal.
Using special tool differential oil seal installer (MB990699), drive the oil seal so that it is flush with the timing chain case.
 

 
 
>>B<< TIMING CHAIN CASE COVER INSTALLATION
1.
cautionSufficiently check that there is no residual oil on the place where degreasing is performed. If fingerprints are left, do not touch it with bare hands after the degreasing, since the oils from your fingers will harm the seal ability.
Remove any liquid gasket remaining on the timing chain case and the timing chain case cover.
cautionThe cover should be installed within 10 minutes of applying liquid gasket.
2. Apply a 2 ± 0.5 mm (0.08 ± 0.01 inch) bead of liquid gasket as illustrated.
Specified sealant:
  • ThreeBond 1217G or equivalent
 

 
 
>>C<< TIMING CHAIN CASE INSTALLATION
1.
cautionSufficiently check that there is no residual oil on the place where degreasing is performed. If fingerprints are left, do not touch it with bare hands after the degreasing, since the oils from your fingers will harm the seal ability.
Remove any liquid gasket remaining on the timing chain case, the cylinder block, and the cylinder head.
2. Install special tool crankshaft front oil seal guide (MB991993) onto the crankshaft.

3.
cautionThe timing chain case should be installed within 10 minutes of applying liquid gasket.
Apply a 2 ± 0.5 mm (0.08 ± 0.01 inch) bead of liquid gasket to location A on the timing chain case respectively as illustrated. [Apply a 1.75 ± 0.5 mm (0.07 ± 0.01 inch) wide bead in the area indicated by *1].
Apply a 1.75 ± 0.5 mm (0.07 ± 0.01 inch) bead of liquid gasket to location B on the timing chain case respectively as illustrated.
Specified sealant
  • A: ThreeBond 1217G or equivalent
  • B: ThreeBond 1227D or equivalent
4. Install the timing chain case.
noteThe mounting bolts have different lengths. Be sure to use the correct bolt for each location.
5. Tighten the chain case mounting bolts to the specified torques.
Tightening torque
  • M6: 9.5 ± 2.5 N·m (84 ± 22 in-lb)
  • M10: 42 ± 16 N·m (31 ± 11 ft-lb)
 

 
 
>>D<< O-RING / WATER PUMP INSTALLATION
1. Carefully remove the coolant dry matters and the other foreign materials from the O-ring groove of the water pump. In the same way, clean the timing chain case side.
2. Push the flange of the new O-ring into the O-ring groove of the water pump to securely install the O-ring. Sufficiently apply water or the coolant to the O-ring with a brush so that the O-ring does not fall.
3. Gently inverting the water pump, check whether the O-ring does not fall.
4. Install the water pump to the timing chain case. At that time, be careful that the O-ring does not fall or the O-ring is not jammed.
 

 
 
>>E<< OIL PAN INSTALLATION
1. Remove any liquid gasket remaining on the cylinder block, the timing chain case, the oil seal case and the oil pan.
2.
cautionThe oil pan should be installed within 10 minutes of applying liquid gasket.
Apply a 2.5 ± 0.5 mm (0.10 ± 0.01 inch) bead of liquid gasket to location A, and a 4 ± 0.5 mm (0.16 ± 0.01 inch) bead of liquid gasket to location B, and a 3 ± 0.5 mm (0.12 ± 0.01 inch) bead of liquid gasket to location C on the oil pan respectively as illustrated.
Specified sealant:
  • ThreeBond 1217G or equivalent
3. Install the oil pan by tightening the fittings to the specified torque of 11 ± 3 N·m (97 ± 26 in-lb).

 
 
>>F<< CYLINDER HEAD COVER INSTALLATION
1. Remove any liquid gasket remaining on the cylinder head cover, the timing chain case and the cylinder head.
2.
cautionThe timing chain should be installed within 3 minutes of applying liquid gasket.
Apply a 4 mm (0.2 in) bead of liquid gasket as illustrated.
Specified sealant:
  • ThreeBond 1217G or equivalent
3. Tighten the bolts to the tightening torque of 2.0 ± 0.5 N·m (18 ± 4 in-lb) in the order shown in the illustration.
4. Next, tighten the bolts to the specified torque of 7.0 ± 0.5 N·m (62 ± 4 in-lb) in the same order.
 

 
 
>>G<< OIL FILTER COVER INSTALLATION
1. Install the oil filer cover so that its portion shown (A) should contact the cylinder block.
2. Depress the counterhold of oil filter cover in front of the engine towards the cylinder block, and tighten the mounting bolt to the specified torque.
Specified torque: 23 ± 6 N·m (17 ± 4 ft-lb)
 

 
 
>>H<< OIL FILTER STUD INSTALLATION
Using special tool oil filter stud setter (MB992676), install the new oil filter stud and tighten it to the specified torque.
Specified torque: 27 ± 2 N·m (20 ± 1 ft-lb)
 

 
 
>>I<< OIL FILTER INSTALLATION
1. Clean the oil filter installing surface on the cylinder block side.
2. Apply a small amount of engine oil to the new oil filter gasket.
3. For the specified tightening torque, refer to the caution label attached on the oil filter.
4. Tighten the oil filter until the gasket contacts with the installation surface.
5. In the same manner as removal, use special tool oil filter wrench (MB991396, MB991828) or commercially-available tool to tighten the oil filter to the specified torque.
6. After installing the oil filter, check clearance between oil filter cover and it.