System Description

SYSTEM DIAGRAM

Part name	Description
Around view monitor control unit	Around View Monitor Control Unit
Front camera	Front Camera
Side camera LH	Side Camera
Side camera RH	Side Camera
Rear camera	Rear Camera
AV control unit	Transmits the camera switch signal to the around view monitor control unit via CAN communication. Receives the camera image signal from the around view monitor control unit by LVDS.
Combination meter	Receiving a buzzer request signal via CAN communication from around view monitor control unit and sound the buzzer. MOD settings can be changed
ABS actuator and electric unit (control unit)	Transmits the following signals to the around view monitor control unit via CAN communication. Vehicle speed signal Front LH wheel speed signal Front RH wheel speed signal Rear LH wheel speed signal Rear RH wheel speed signal Steering angle sensor signal
BCM	Transmits the following signals to the around view monitor control unit via CAN communication. Door switch signal Back door switch signal High beam request signal Low beam request signal Position light request signal Front fog light request signal Turn indicator signal
PHEV-ECU	Transmits shift position signal to the around view monitor control unit via CAN communication.
Sonar control unit	Transmits sonar indicator display signal to the around view monitor control unit via CAN communication.

Around View Monitor Control Unit Input Signal (CAN Communication)

Transmit unit	Signal name
AV control unit	Camera switch signal
AV control unit	Language setting signal
Combination meter	MOD setting signal
ABS actuator and electric unit (control unit)	Vehicle speed signal
	Front LH wheel speed signal
	Front RH wheel speed signal
	Rear LH wheel speed signal
	Rear RH wheel speed signal
	Steering angle sensor signal
BCM	Door switch signal
	Back door switch signal
	High beam request signal
	Low beam request signal
	Position light request signal
	Front fog light request signal
	Back door switch signal
PHEV-ECU	Shift position signal
Sonar control unit	Sonar status signal
ADAS ECU	CTA signal

Around View Monitor Control Unit Output Signal (CAN Communication)

Transmit unit	Signal name
AV control unit	View change signal
Combination meter	Buzzer output signal
Combination meter	MOD setting status signal

DESCRIPTION

This system is equipped with wide-angle high-resolution cameras on the front and rear of the vehicle and on both right and left door mirrors. The images from front view, rear view, front-side view passenger side, and birds-eye view that shows the view from the top of the vehicle are displayed to monitor the vehicle surroundings.
Around view monitor control unit cuts out and expands the image received from each camera to create each view.
The sonar indicator is displayed on display (superimposed on the camera image) in combination with the sonar system to warm of the approach of an obstacle.
Camera image is displayed on the display when an obstacle is detected by sonar system.
In front view and rear view, the vehicle width, distance lines and predictive course lines are superimposed and displayed. In front-side view, the vehicle distance guiding line and vehicle width guiding line are displayed.
The Birds-Eye view converts the images from 4 cameras into the overhead view and displays the status of the vehicle on display. The vehicle icon and sonar indicator that are displayed on the Birds-Eye view display are rendered by around view monitor control unit.
Moving Object Detection (MOD) is adopted that detects moving objects according to camera image and notifies the detection result to the driver.
Front/rear wide view function is adopted. Visibility for the left and right that contains invisible area is improved.

AROUND VIEW MONITOR SCREEN

Around view monitor combines and displays the travel direction view and “Birds-Eye view”, “Front-Side view” and then it displays the sonar indicator on the “Birds-Eye view”, “Front-Side view”, "Front wide view" and “Rear wide view”.
Around view monitor control unit renders the view icon, warning message on display.

Screen Constitution

OPERATION DESCRIPTION

Around view monitor screen transition

Around view monitor is displayed on the display when “CAMERA” switch is pressed, when shifting position is reverse, or when an obstacle is detected by sonar system.
Birds-Eye view, Front-side view, and front/rear wide view can be switched by “CAMERA” switch, while around view monitor is displayed.
While shift position is other than reverse, around view monitor is cancelled when approximately 3 minutes are passed after “CAMERA” switch is pressed, or when vehicle speed is approximately 10 km/h (6 MPH) or more. The screen returns to the screen before displaying around view monitor.
Setting of Moving Object Detection (MOD) and sonar can be switched ON/OFF by combination meter.
In D position, front sonar can detect an obstacle while camera image is not displayed on AV control unit. Screen is switched to camera image when an obstacle is detected.
When “CAMERA” switch is pressed, it receives camera switch signal from AV control unit via CAN communication.
When around view monitor control unit receives camera switch signal, around view monitor control unit reads the image signal from each camera.
When around view monitor control unit receives reverse signal, while shift position is R position, around view monitor control unit reads image signal from each camera by LVDS.
When around view monitor control unit reads image signal from each camera, it cuts out the required screen for each view, superimposes camera image, vehicle icon, guiding lines, predicted course line, “MOD” icon, and sonar indicator, and then outputs them to AV control unit by LVDS.

Front View

The front view image is from the front camera.
When the selector lever is in any position other than the reverse position, the front view is displayed by pressing the “CAMERA” switch. It improves the visibility of obstacles in front of the vehicle and helps driving by the images displayed from Birds-Eye view and Front-Side view. The front wide view function allows the display of an image with an approximately 180° horizontal angle.
Display the vehicle width guiding line and vehicle distance guiding line in front view and display the predictive course line according to the steering angle.
If the steering angle is within approximately 90 degrees, the predictive course lines on the left/right side are displayed. If the steering angle is exceeding approximately 90 degrees, only the predictive course line on the outside (in the opposite side of steering direction) is displayed.
Around view monitor control unit receives the steering angle signal from ABS actuator and electric unit (control unit) via CAN communication.
Around view monitor control unit controls the direction of the predictive course line according to the steering sensor angle signal.

Front view guiding lines

Rear View

The rear view image is from the rear camera.
When the selector lever is in the reverse position, the rear view is displayed. Backing and parking are improved by the images from Birds-Eye view and Front-Side view. The rear wide view function allows the display of an image with an approximately 180° horizontal angle.
Display the vehicle width guiding line and vehicle distance guiding line in rear view and display the predictive course line according to the steering angle.
The predictive course line is not displayed at the steering neutral position.
Around view monitor control unit receives the steering angle signal from ABS actuator and electric unit (control unit) via CAN communication.
Around view monitor control unit controls the direction and distance of predictive course line according to the steering angle sensor signal.
Rear view guiding lines

Front-side View

The front-side view image is from the side camera RH.
In front-side view, display the vehicle distance guiding line and vehicle width guiding line.

Front-side view area and guiding line

Birds-eye View

The image from the 4 cameras is cut out and converted into the overhead view, and the surroundings of the vehicle is displayed in birds-eye view.

Birds-Eye view display image

Birds-Eye view display area

Moving Object Detection (MOD)

Moving Object Detection (MOD) is a function that notifies the driver of the presence of moving objects in the area around the vehicle. MOD detects moving objects from camera image, illuminates frame of view in yellow whenever “MOD” icon is displayed in green, and sounds buzzer.
MOD detects moving objects while camera image is displayed on AV control unit.
Around view monitor control unit performs the following process when moving objects are detected.
- Superimposes yellow frame line on camera image signal and outputs them to AV control unit by LVDS.
- Transmits MOD beep sound output request signal to combination meter via CAN communication.
- Combination meter that receives the MOD beep sound output request signal from around view monitor control unit, and outputs buzzer drive signal to buzzer.
Around view monitor control unit detects moving objects from camera image according to an image recognition method called optical flow.
MOD does not detect a background as a moving object when the vehicle moves (when whole screen moves), but detects a moving object when an actual moving object is displayed on screen.
MOD can be set to permanent OFF by the following operation.
- Permanent OFF: Settings can be performed on the information display of the combination meter.

Color of “MOD” icon indicates whether or not MOD is operative. “MOD” icon is displayed as shown in the following table. when MOD is operative, “MOD” icon is displayed in green. when MOD is not operative, “MOD” icon is displayed in gray. MOD icon is not displayed when MOD is OFF by “Settings”.

View		Shift position
		P or N position	D position	R position
		“MOD” icon display
Birds-Eye view and front view	Birds-Eye view	Green	Gray	–
Birds-Eye view and front view	Front view	Gray	Green	–
Side view and front view	Side view	×	×	–
Side view and front view	Front view	Gray	Green	–
Birds-Eye view and rear view	Birds-Eye view	Green	–	Gray
Birds-Eye view and rear view	Front view	Gray	–	Green
Side view and rear view	Side view	×	–	×
Side view and rear view	Rear view	Gray	–	Green
Rear wide view		–	–	Green
Front wide view		Gray	Green	–

×: Icon is not displayed.

–: View is not displayed in each shift position (D position and R position).

MOD illuminates frame of view in yellow and sounds buzzer, when any of the conditions in the following table are satisfied.

Operation Condition		View where MOD is operative
Shift position	Vehicle speed	View where MOD is operative
P or N position	0 km/h (0 MPH)	Birds-Eye view
D position	0 km/h (0 MPH) or more - less than 8 km/h (5 MPH)	Front view Front wide view
R position	0 km/h (0 MPH) or more - less than 8 km/h (5 MPH)	Rear view Rear wide view

MOD does not operate or stops operation when any of the conditions in the following table are satisfied.

Operation stop condition	Note
Door open	MOD does not stop operation for front view and front wide view. Operation stops for rear view and rear wide view while back door is open. Operation stops for Birds-Eye view when any door is open.
Door mirror expanding/retracting	Expanding/retracting status of door mirror is judged according to operation signal of door mirror motor transmitted from door mirror (driver side) to around view monitor control unit.

MAC (Message Authentication Code)

MAC (Message Authentication Code) is a function that prevents unauthorized communication from other than the ECU with MAC function by secure authentication communication. Around view monitor control unit can write a MAC key required for communication between the ECUs and perform MAC diagnosis.