System Description

SYSTEM DIAGRAM

Door lock function controls operation function of the following items.

Door lock and unlock function (door request switch)
Selective unlock function (door request switch)
Reminder function (door request switch)
Auto door lock function (door request switch)

DOOR LOCK AND UNLOCK FUNCTION (DOOR REQUEST SWITCH)

When pressing the door request switch, it is possible to lock and unlock the door by carrying the keyless operation key.

OPERATION DESCRIPTION

When the keyless operation key unit detects that each door request switch is pressed, it starts the keyless operation outer antenna and keyless operation rear inner antenna corresponding to the pressed door request switch and transmits the request signal to the keyless operation key. And then, check that the keyless operation key is near the door.
If the keyless operation key is within the keyless operation outer antenna detection area, it receives the request signal and transmits the key ID signal to the keyless operation key unit via remote keyless entry receiver.
Keyless operation key unit receives the key ID signal and compares it with the registered key ID to the vehicle.
If the verification result is OK, keyless operation key unit transmits the door lock/unlock request signal to BCM via CAN communication.
BCM transmits door lock/unlock request signal to each door lock actuator, activates each door lock actuator when receiving door lock/unlock request signal from keyless operation key unit.

OPERATION CONDITION

If the following conditions are satisfied, door lock and unlock operation is performed if the door request switch is operated.

Each door request switch operation	Operation condition
Lock	Keyless operation key is outside the vehicle P position warning is not activated Selective unlock function is not activated Keyless operation key is within keyless operation outer antenna detection area* All doors closed
Unlock	Keyless operation key is outside the vehicle Keyless operation key is within keyless operation outer antenna detection area *

*: Even with a registered keyless operation key remaining inside the vehicle, door lock or unlock can be operated from outside of the vehicle with a spare keyless operation key as long as key IDs are different.

SELECTIVE UNLOCK FUNCTION (DOOR REQUEST SWITCH)

When the request switch is pushed, only the corresponding door is unlocked.

From the "Locking" menu, select "Selective Unlock". Use the scroll dial to activate or deactivate this function. If you deactivate this function, all the doors will be unlocked by pressing the request switch.

LOCK OPERATION

When lock signal is sent from door request switch, all doors are locked.

Unlock Operation

When unlock signal from front door request switch LH is transmitted, front door LH unlocks. When front door request switch LH is operated again within 2 seconds, all door unlock.
When unlock signal from front door request switch RH is transmitted, front door RH unlock. When front door request switch RH is operated again within 2 seconds, all doors unlocks.
When unlock signal from back door request switch is transmitted, back door unlock. When back door request switch is operated again within 2 seconds, all doors unlocks.

REMINDER FUNCTION (DOOR REQUEST SWITCH)

When doors are locked or unlocked by door request switch, BCM blinks hazard warning lights as a reminder or keyless operation buzzer signal to keyless operation key unit via CAN communication. Reminder function does not operate if electric motor switch in ON position. The reminder function has C mode and S mode.

Operation	C mode		S mode
Door request switch	Lock	Unlock	Lock	Unlock
Hazard warning light	Once	Twice	Once	–
Keyless operation buzzer	Once*	Twice	–	–

*: Work support mode [ANSWER BACK] setting is "On"

How to Change Reminder Function Operation Mode

Reminder function operation mode can be changed using combination meter setting.
When lock and unlock signal are sent from the keyless operation key for more than 4 seconds at the same time, the hazard and buzzer reminder mode is changed and hazard warning light blinks and horn sounds as per the following items:

AUTO DOOR LOCK FUNCTION (DOOR REQUEST SWITCH)

After door is unlocked by door request switch operation and if 30 seconds or more passes without performing the following operation, all doors are automatically locked. However, operation check function does not activate.

Operating condition

Door switch is ON (each door is open)
Keyless operation key unit receives door lock signal
Electric motor switch is pressed

KEYLESS OPERATION OUTER ANTENNA DETECTION AREA

The keyless operation outer antenna detection area of door lock/unlock function is in the range of approximately 0.7 m (27.56 in) surrounding the front door request switch

and back door request switch

. However, this operating range depends on the ambient conditions.

LIST OF OPERATION RELATED PARTS

Parts marked with × are the parts related to operation.

Function	Keyless operation key	Keyless operation key unit	Door switch	Door request switch	Door lock actuator	Keyless operation rear inner antenna	Keyless operation outer antenna	Keyless operation buzzer	CAN communication system	BCM	Hazard warning light	Electric motor switch	Combination meter
Door lock and unlock function (door request switch)	×	×	×	×	×	×	×			×
Selective unlock function (door request switch)	×	×	×	×	×	×	×			×
Reminder function (door request switch)								×	×	×	×		×
Auto door lock function (door request switch)	×		×	×	×					×		×