[Previous][Next]
DTC Description
 
 
DTC DETECTION LOGIC
DTC No.M.U.T.-III SE screen terms
(Trouble diagnosis content)
DTC detection condition
C106107FR LH wheel sensor
(Front left wheel sensor)
1Diagnosis condition
  • When electric motor switch is ON.
  • When front left wheel sensor power supply voltage is normal.
  • When the vehicle speed is 10 km/h (6.2 MPH) – 60 km/h (37 MPH).
Signal (terminal)Front left wheel sensor signal
ThresholdWhen distance between front left wheel sensor and front left wheel sensor rotor is large.
Diagnosis delay time1 – 60 seconds or more
2Diagnosis condition
  • When electric motor switch is ON.
  • When front left wheel sensor power supply voltage is normal.
  • When the vehicle speed is 10 km/h (6.2 MPH) – 60 km/h (37 MPH).
Signal (terminal)Front left wheel sensor signal
ThresholdWhen installation of front left wheel sensor or front left wheel sensor rotor is not normal.
Diagnosis delay time1 – 60 seconds or more
3Diagnosis condition
  • When electric motor switch is ON.
  • When front left wheel sensor power supply voltage is normal.
  • When the vehicle speed is 10 km/h (6.2 MPH) – 60 km/h (37 MPH).
Signal (terminal)Front left wheel sensor signal
ThresholdWhen there is contamination on or damage to the front left wheel sensor or rear RH sensor rotor.
Diagnosis delay time1 – 60 seconds or more
 
 
POSSIBLE CAUSE
noteConfirm if DTC is Stored DTC or Active DTC. If DTC is Active DTC, proceed with Diagnosis Procedure. If DTC is Stored DTC, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a Stored DTC DTC.
Stored DTC DTCActive DTC DTC
  • Harness or connector
  • Front left wheel sensor
  • Front left sensor rotor
  • Front left tire size
  • ABS actuator and electric unit (control unit) power supply system
  • Fuse
  • Fusible link
  • 12V battery
  • Vehicle was not driven after previous repair
  • Harness or connector
  • Front left wheel sensor
  • Front left sensor rotor
  • Front left tire size
  • ABS actuator and electric unit (control unit)
  • ABS actuator and electric unit (control unit) power supply system
  • Fuse
  • Fusible link
  • 12V battery
 
 
FAIL-SAFE
The following functions are suspended.
  • ASC function
  • TCS function
  • ABS function
  • EBD function
  • Brake limited slip differential (BLSD) function
  • Brake assist function
  • Brake force distribution function
  • hill start assist function
  • Electric parking brake function
  • Hill Descent Control funciton
 
 
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE" has been previously conducted, always electric motor switch OFF (Auto ACC function OFF) before conducting the next test.
: .
 
2.CHECK DTC DETECTION
With M.U.T.-III SE
  1. Electric motor switch ON.
  2. Drive the vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.
  3. Stop the vehicle.
  4. Electric motor switch OFF (Auto ACC function OFF).
  5. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  6. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C1061-07" detected?
-1“Active DTC" is displayed: Refer to Diagnosis Procedure.
-2“Stored DTC" is displayed: INSPECTION END (Erase the memory of Diagnostic Trouble Code results.)
-1To check malfunction symptom before repair: Refer to Intermittent IncidentIntermittent Incident.
-2Confirmation after repair: INSPECTION END