[Previous][Next]
System Description
 
 
SYSTEM DIAGRAM
ComponentFunction
Door switchDoor switch detects door switch condition and then transmits door switch signal to BCM.
Inside key antennaInside key antenna detects whether Keyless operation key is inside the vehicle, and transmits the key ID signal to Keyless operation key unit.
Stop light switchStop light switch detects that brake pedal is depressed, and then transmits stop light switch signal to BCM.
ABS actuator and electric unit (control unit)ABS actuator and electric unit (control unit) transmits the vehicle speed signal to BCM via CAN communication.
TCMTCM receives the P/N position signal from transmission range switch, and then transmits the shift position signal to BCM via CAN communication.
ECM
  • ECM controls the engine.
  • When ignition switch is turned ON, Keyless operation key unit starts communication with ECM and performs the ID verification between Keyless operation key unit and ECM.
  • If the verification result is OK, the engine can start. If the verification result is NG, the engine cannot start.
IPDM E/RStarter cut relay is controlled by BCM, and starter relay is controlled by IPDM E/R while communicating with BCM.
BCMWhen BCM receives a starter cut relay request signal from ECM, the starter cut relay is turned ON.
Push-button ignition switchPush switch
  • Push-button ignition switch has push switch inside which detects that push-button ignition switch is pressed, and then transmits the push switch signal to Keyless operation key unit.
  • Keyless operation key unit changes the ignition switch position with the operation of push-button ignition switch.
  • Keyless operation key unit maintains the ignition switch position status while push-button ignition switch is not operated.
NATS antenna amp.
Keyless operation keyThe Keyless operation key system is a system that makes it possible to lock and unlock the door locks (door lock/unlock function) by carrying the Keyless operation key, which operates based on the results of electronic ID verification using two-way communication between the Keyless operation key and the vehicle (Keyless operation key unit).
Keyless operation key unit
  • Keyless operation key unit controls INTELLIGENT KEY SYSTEM (ENGINE START FUNCTION)
  • Keyless operation key unit performs the ID verification between Keyless operation key unit and Keyless operation key when the Keyless operation key is carried into the detection area of inside key antenna, and push-button ignition switch is pressed. If the ID verification result is OK, ignition switch operation is available.
  • Then, when the ignition switch is turned ON, Keyless operation key unit performs ID verification between Keyless operation key unit and ECM. If the ID verification result is OK, ECM can start engine.
TCUTCU transmits engine start request signal to BCM when engine start request is received from Infiniti ConnectionTM data center.
 
 
BCM INPUT/OUTPUT SIGNAL CHART
 
 
Input Signal Item
Transmit unitSignal name
ECMCAN communication
  • Engine status signal
  • Starter cut relay request signal
IPDM E/R
  • Ignition ON signal
  • Starter cut relay status signal
  • Neutral position signal
ABS actuator and electric unit (control unit)Vehicle speed signal
TCMShift position signal
TCUEngine start request signal
Each door switchDoor switch signal
Stop light switchStop light switch signal
 
 
Output Signal Item
Reception unitSignal name
IPDM E/RCAN communicationIgnition ON signal
 
 
INTELLIGENT KEY UNIT INPUT/OUTPUT SIGNAL CHART
 
 
Input Signal Item
Transmit unitSignal name
IPDM E/RCAN communicationIgnition ON signal
 
 
Output Signal Item
Reception unitSignal name
IPDM E/RCAN communicationIgnition ON signal
Inside key antennaKey ID request signal
 
 
SYSTEM DESCRIPTION
  • The engine start function of Keyless operation key system makes it possible to start and stop the engine without using the key, based on the electronic ID verification. The electronic ID verification is performed between Keyless operation key unit and Keyless operation key when the push-button ignition switch is pressed while the Keyless operation key is within the detection area of inside key antenna.
    noteThe driver should carry the Keyless operation key at all times.
  • Keyless operation key have ID (Key ID). It can perform the door lock/unlock operation and the push-button ignition switch operation when the registered Keyless operation key is carried.
  • If the ID is successfully verified, when push-button ignition switch is pressed, engine can be started.
  • Up to 4 Intelligent Keys can be registered (Including the standard Keyless operation key) upon request from the customer.
    noteFor any functions other than engine start function of Keyless operation key system. Refer to System Description.
 
 
PRECAUTIONS FOR INTELLIGENT KEY SYSTEM
The transponder (the chip for NATS ID verification) is integrated into the Keyless operation key. It is integrated into the mechanical key. Therefore, ID verification cannot be performed by mechanical key only.
In that case, NATS ID verification can be performed when Keyless operation key backside is contacted to push-button ignition switch while brake pedal is depressed. If verification result is OK, engine can be started.
 
 
OPERATION WHEN INTELLIGENT KEY IS CARRIED
  1. When the push-button ignition switch is pressed, the Keyless operation key unit activates the inside key antenna and transmits the request signal to the Keyless operation key.
  2. The Keyless operation key receives the request signal and transmits the NATS ID signal to the Keyless operation key unit.
  3. Keyless operation key unit receives the NATS ID signal verifies it with the registered ID.
  4. When the ignition switch is turned to ON, Keyless operation key unit performs ID verification with the ECM. When the result is OK, engine start is permitted.
  5. When ECM detects that the start engine conditions* are satisfied, it transmits a starter cut relay request signal to BCM.
  6. When BCM receives a starter cut relay request signal from ECM, the starter cut relay is turned ON.
  7. When starter cut relay is turned ON, IPDM E/R turns ON the starter relay and drives the starter motor.
  8. When BCM receives an engine status signal from ECM, it turns the starter relay and starter cut relay OFF and stops cranking.
    cautionWhen the Keyless operation key is carried outside of the vehicle (outside key antenna detection area) while the power supply is in the ON position, even if the engine start condition* is satisfied, the engine cannot be started.
*: For the engine start condition, refer to “IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION”.
 
 
OPERATION RANGE
Engine can be started when Keyless operation key is inside the vehicle. However, sometimes engine may not start when Keyless operation key is on instrument panel or in glove box.
 
 
IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION
The ignition switch position can be changed by the following operations.
note
  • When an Keyless operation key is within the detection area of inside key antenna or when Keyless operation key backside is contacted to push-button ignition switch, it is equivalent to the operations below.
  • When starting the engine, the BCM monitors under the engine start conditions.
    • Brake pedal operation condition
    • Selector lever position
    • Vehicle speed
 
 
Vehicle speed: less than 4 km/h (2.5 MPH)
Power supply positionConditionPush-button ignition switch operation frequency
Selector leverBrake pedal operation condition
OFF → ONNot depressed1
OFF → ON → OFFNot depressed2
OFF → START
ON → START
P or N positionDepressed1
Engine is running → OFF1
noteIf the Keyless operation key unit cannot detect that the Keyless operation key is in the vehicle, ignition switch can be turned OFF by the press and hold the push-button ignition switch for 2 seconds or more.
 
 
Vehicle speed: 4 km/h (2.5 MPH) or more
Power supply positionConditionPush-button ignition switch operation frequency
Selector leverBrake pedal operation condition
Engine is running → OFF Emergency stop operation
Engine stall return operation while driving N positionNot depressed1
Emergency stop operation
  1. Press and hold the push-button ignition switch for 2 seconds or more.
  2. Press the push-button ignition switch 3 times or more within 1.5 seconds.
 
 
REMOTE ENGINE START FUNCTION
Remote engine start function enables engine to be started from vehicle outside by operating remote engine start button of Keyless operation key or cellular phone.
In the same way as the Keyless operation key, the engine can be started by operating a cellular phone using the Telematics system function.
 
 
Engine Start Procedures
The following operation enables the engine to be started.
  • Perform engine start operation using a cellular phone.
Engine does not start while the vehicle is in the following status.
  • All doors are UNLOCK or any door is open.
  • Hood is open.
  • A registered Keyless operation key is in passenger room.
  • Shift position is other than P.
  • Vehicle security alarm is in operation.
  • Hazard light is in operation.
 
 
Engine Stop Procedures
The following operation enables the engine to be stopped.
  • Press remote engine start button of Keyless operation key.
  • Perform engine stop operation using a cellular phone.
  • Push-button ignition switch is operated.
Engine stops when the vehicle status changes to the following status.
  • 10 minutes are passed since engine start.
  • Hood is open.
  • Shift position is shifted to a position other than P.
  • Vehicle security alarm starts to operate.
noteWhile engine is in operation by Keyless operation key, engine operation time can be extended for 10 minutes. To extend engine operation time, press LOCK button of Keyless operation key, and then within 5 seconds, press and hold remote engine start button of Keyless operation key for 2 seconds or more.
 
 
Operation Area
The engine can be started when the vehicle is under the following conditions.
  • The remote engine start operating range is approximately 60 m (197 ft.) from the vehicle.
  • The vehicle is within the communication range of the Infiniti Connection™ data center.