[Previous][Next]
M.U.T.-III SE Function
 
 
APPLICABLE ITEM
Diagnosis modeDescription
Self Diagnostic ResultDisplay DTC which TCM memorizes
Data ListDisplays TCM input/output data in real time
Special Function
  • Displays TCM part number
  • This mode enables a technician to adjust some devices faster and more accurately
CALIB DATAThe calibration data status of TCM can be checked
 
 
SELF DIAGNOSTIC RESULTS
 
 
Display Item List
Refer to DTC Index.
 
 
How to Read DTC
DTC is displayed on "Self Diagnostic results" of M.U.T.-III SE.
When DTC is currently detected, "Active DTC" is displayed. If "Stored DTC" is displayed, it shows a malfunction occurred in the past.
 
 
How to Erase DTC
noteIf the ignition switch is left ON after repair, turn OFF the ignition switch and wait for 10 seconds or more. Then, turn the ignition ON again. (Engine stop)
  1. Touch "SHIFT" of M.U.T.-III SE.
  2. Touch "Self Diagnostic Result".
  3. Touch "Erase DTCs". (DTC memorized in electric shift control module is erased.)
 
 
Freeze Frame Data (FFD)
The following vehicle status is recorded when DTC is detected and is displayed on M.U.T.-III SE.
Monitored itemDisplayed contents
ODO/TRIP METERDisplays the mileage at the time the malfunction is detected.
DTC count (Count)Displays the number of times DTC is detected.
 
 
DATA MONITOR
noteThe following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to M.U.T.-III SE display items.
Monitored item(Unit)Remarks
Range positionDisplays the position recognized by the electric shift control module
Shift position judgmentDisplays the shift input position recognized by the electric shift control module
Target shift positionDisplays the target shift position recognized by the electric shift control module
Actual shift positionDisplays the shift position signal received from TCM
Vehicle stateDisplays the status of vehicle
  • State1: Ignition switch OFF
  • State2: Ignition switch is ACC
  • State3: Ignition switch is ON (Engine is stopped)
  • State4: While engine starting
  • State5: Engine started
Shift sensor 1Displays the signal value of electric shift sensor No. 1
Shift sensor 2Displays the signal value of electric shift sensor No. 2
Shift sensor 3Displays the signal value of electric shift sensor No. 3
Shift sensor 4Displays the signal value of electric shift sensor No. 4
Shift sensor 5Displays the signal value of electric shift sensor No. 5
Shift sensor 6Displays the signal value of electric shift sensor No. 6
Shift sensor 7Displays the signal value of electric shift sensor No. 7
Shift sensor 8Displays the signal value of electric shift sensor No. 8
Shift switch 1Displays the signal value of P position switch No. 1
Shift switch 2Displays the signal value of P position switch No. 2
Power supply relay ADisplays the command value from the electric shift control module to shift actuator relay A
Power supply relay BDisplays the command value from the electric shift control module to shift actuator relay B
Ignition switchDisplays the input status of the ignition switch
Power supply voltageDisplays the status of battery voltage
ECU power 1Monitors the power supply of electric shift control module and displays the status
Main power voltage(V)Monitors the voltage value of the main power supply for the electric shift control module and displays the monitored value
ECU power 2Monitors the power supply of electric shift control module and displays the status
Motor A U voltage(V)Displays the motor A U-phase terminal voltage A/D converted value
Motor A V voltage(V)Displays the motor A V-phase terminal voltage A/D converted value
Motor A W voltage(V)Displays the motor A W-phase terminal voltage A/D converted value
Motor B U voltage(V)Displays the motor B U-phase terminal voltage A/D converted value
Motor B V voltage(V)Displays the motor B V-phase terminal voltage A/D converted value
Motor B W voltage(V)Displays the motor B W-phase terminal voltage A/D converted value
Shift sensor 1 voltage(V)Displays the voltage value of electric shift sensor No. 1
Shift sensor 2 voltage(V)Displays the voltage value of electric shift sensor No. 2
Shift sensor 3 voltage(V)Displays the voltage value of electric shift sensor No. 3
Shift sensor 4 voltage(V)Displays the voltage value of electric shift sensor No. 4
Shift sensor 5 voltage(V)Displays the voltage value of electric shift sensor No. 5
Shift sensor 6 voltage(V)Displays the voltage value of electric shift sensor No. 6
Shift sensor 7 voltage(V)Displays the voltage value of electric shift sensor No. 7
Shift sensor 8 voltage(V)Displays the voltage value of electric shift sensor No. 8
Shift switch 1 voltage(V)Displays the voltage value of P position switch No. 1
Shift switch 2 voltage(V)Displays the voltage value of P position switch No. 2
 
 
WORK SUPPORT
Function nameItem nameDescription
ECU Information-Displays TCM part number
Learned value clearACTUATOR LEARNING VALVE ELIMINATIONErases learning value memorized by electric shift control module.