[Previous][Next]
DTC Diagnosis Procedure
1.CHECK TCM INPUT SIGNALS
With M.U.T.-III SE
  1. Start the engine.
  2. Select “Data List” in “TRANSMISSION”.
  3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, and “P POSITION SW”.
  4. Check ON/OFF of each monitor item.
    Monitor itemTest conditionCondition
    D POSITION SWShift position: “D” positionOn
    Other than the aboveOff
    N POSITION SWShift position: “N” positionOn
    Other than the aboveOff
    R POSITION SWShift position: “R” positionOn
    Other than the aboveOff
    P POSITION SWShift position: “P” positionOn
    Other than the aboveOff
Without M.U.T.-III SE
  1. Start the engine.
  2. Disconnect TCM connector.
  3. The ignition switch is ON.
  4. Check voltage between TCM harness connector terminals and ground.
    +Test conditionVoltage
    TCM
    ConnectorTerminal
    F754GroundShift position: “D” position10 – 16 V
    Other than the aboveApprox. 0 V
    5Shift position: “N” position10 – 16 V
    Other than the aboveApprox. 0 V
    6Shift position: “R” position10 – 16 V
    Other than the aboveApprox. 0 V
    7Shift position: “P” position10 – 16 V
    Other than the aboveApprox. 0 V
Is the inspection result normal?
Check intermittent incident. Refer to Intermittent IncidentIntermittent Incident.
-1“D POSITION SW” is “ON” when selector is not in “D” position. Or connector terminal 4 is at power voltage : .
-2“N POSITION SW” is “ON” when selector is not in “N” position. Or connector terminal 5 is at power voltage : .
-3 “R POSITION SW” is “ON” when selector is not in “R” position. Or connector terminal 6 is at power voltage : .
-4“P POSITION SW” is “ON” when selector is not in “P” position. Or connector terminal 7 is at power voltage : .
 
2.CHECK D POSITION SW CIRCUIT (PART 1)
  1. The ignition switch is OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.
    TCMContinuity
    ConnectorTerminal
    F7542Not existed
    5
    6
    7
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
3.CHECK D POSITION SW CIRCUIT (PART 2)
  1. Disconnect transmission range switch connector.
  2. The ignition switch is ON.
  3. Check voltage between TCM harness connector terminal and ground.
    +Voltage
    (Approx.)
    TCM
    ConnectorTerminal
    F754Ground0 V
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
4.CHECK N POSITION SW CIRCUIT (PART 1)
  1. The ignition switch is OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.
    TCMContinuity
    ConnectorTerminal
    F7552Not existed
    4
    6
    7
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
5.CHECK N POSITION SW CIRCUIT (PART 2)
  1. Disconnect transmission range switch connector.
  2. The ignition switch is ON.
  3. Check voltage between TCM harness connector terminal and ground.
    +Voltage
    (Approx.)
    TCM
    ConnectorTerminal
    F755Ground0 V
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
6.CHECK P POSITION SW CIRCUIT (PART 1)
  1. The ignition switch is OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.
    TCMContinuity
    ConnectorTerminal
    F7572Not existed
    4
    5
    6
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
7.CHECK P POSITION SW CIRCUIT (PART 2)
  1. Disconnect transmission range switch connector.
  2. The ignition switch is ON.
  3. Check voltage between TCM harness connector terminal and ground.
    +Voltage
    (Approx.)
    TCM
    ConnectorTerminal
    F757Ground0 V
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
8.CHECK R POSITION SW CIRCUIT (PART1)
  1. The ignition switch is OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.
    TCMContinuity
    ConnectorTerminal
    F7562Not existed
    4
    5
    7
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
9.CHECK R POSITION SW CIRCUIT (PART 2)
  1. Disconnect transmission range switch connector.
  2. The ignition switch is ON.
  3. Check voltage between TCM harness connector terminal and ground.
    +Voltage
    (Approx.)
    TCM
    ConnectorTerminal
    F756Ground0 V
Is the inspection result normal?
.
Repair or replace malfunctioning parts.
 
10.CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to Component Inspection.
Is the check result normal?
Check intermittent incident. Refer to Intermittent IncidentIntermittent Incident.
Repair or replace malfunctioning parts.