Diagnosis Procedure

1.CHECK ELECTRIC SHIFT CONTROL MODULE INPUT VOLTAGE

With M.U.T.-III SE

The ignition switch is ON.
Select “Data List” in “SHIFT”.
Select “Shift sensor 1 voltage”, “Shift sensor 2 voltage”, “Shift sensor 3 voltage”, “Shift sensor 4 voltage”, “Shift sensor 5 voltage”, “Shift sensor 6 voltage”, “Shift sensor 7 voltage”, and “Shift sensor 8 voltage”.

Operate the selector lever and check the voltage.

Monitor item	Condition	Value / Status
Shift sensor 1 voltage	Selector lever is held in H (Home), R, and Nr positions	1.08 - 2.12 V
Shift sensor 1 voltage	Other than the above	2.68 - 3.28 V
Shift sensor 2 voltage	Selector lever is held in H (Home), R, and Nr positions	1.08 - 2.12 V
Shift sensor 2 voltage	Other than the above	2.68 - 3.28 V
Shift sensor 3 voltage	Selector lever is held in H (Home) and Nr positions	1.08 - 2.12 V
Shift sensor 3 voltage	Other than the above	2.68 - 3.28 V
Shift sensor 4 voltage	Selector lever is held in H (Home), Nr, and Nd positions	1.08 - 2.12 V
Shift sensor 4 voltage	Other than the above	2.68 - 3.28 V
Shift sensor 5 voltage	Selector lever is held in H (Home), Nr, and Nd positions	1.08 - 2.12 V
Shift sensor 5 voltage	Other than the above	2.68 - 3.28 V
Shift sensor 6 voltage	Selector lever is held in H (Home) and Nd positions	1.08 - 2.12 V
Shift sensor 6 voltage	Other than the above	2.68 - 3.28 V
Shift sensor 7 voltage	Selector lever is held in H (Home), D/M, and Nd positions	1.08 - 2.12 V
Shift sensor 7 voltage	Other than the above	2.68 - 3.28 V
Shift sensor 8 voltage	Selector lever is held in H (Home), D/M, and Nd positions	1.08 - 2.12 V
Shift sensor 8 voltage	Other than the above	2.68 - 3.28 V

Without M.U.T.-III SE

Check the voltage between the electric shift control module harness connector terminal and ground.

Electric shift sensor	+		−	Condition	Voltage (Approx.)
	Electric shift control module
	Connector	Terminal
1	E131	34	Ground	Selector lever is held in H (Home), R, and Nr positions	1.08 - 2.12 V
1		34		Other than the above	2.68 - 3.28 V
2		35		Selector lever is held in H (Home), R, and Nr positions	1.08 - 2.12 V
2		35		Other than the above	2.68 - 3.28 V
3		36		Selector lever is held in H (Home) and Nr positions	1.08 - 2.12 V
3		36		Other than the above	2.68 - 3.28 V
4		37		Selector lever is held in H (Home), Nr, and Nd positions	1.08 - 2.12 V
4		37		Other than the above	2.68 - 3.28 V
5		44		Selector lever is held in H (Home), Nr, and Nd positions	1.08 - 2.12 V
5		44		Other than the above	2.68 - 3.28 V
6		45		Selector lever is held in H (Home) and Nd positions	1.08 - 2.12 V
6		45		Other than the above	2.68 - 3.28 V
7		39		Selector lever is held in H (Home), D/M, and Nd positions	1.08 - 2.12 V
7		39		Other than the above	2.68 - 3.28 V
8		40		Selector lever is held in H (Home), D/M, and Nd positions	1.08 - 2.12 V
8		40		Other than the above	2.68 - 3.28 V

Is the inspection results normal?

INSPECTION END

2.CHECK ELECTRIC SHIFT SELECTOR INPUT VOLTAGE

Check the voltage between electric shift selector harness connector terminal and ground.

Is the inspection results normal?

3.CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR - 1

The ignition switch is OFF.
Disconnect the electric shift selector connector.
Disconnect the electric shift control module connector.
Check the continuity between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.
Electric shift control module Electric shift selector Continuity
Connector Terminal Connector Terminal
E130 19 M2 1 Existed
E131 48 13
Check the continuity between the electric shift control module harness connector terminal and ground.
Electric shift control module — Continuity
Connector Terminal
E130 19 Ground Not existed
E131 48

Electric shift control module	Electric shift selector	Continuity
E130	19	M2	1	Existed
E131	48	13

Electric shift control module	—	Continuity
E130	19	Ground	Not existed
E131	48

Is the inspection results normal?

Check intermittent incident. Refer to Intermittent IncidentIntermittent Incident

Repair or replace damaged parts.

4.CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR - 2

Electric shift sensor	Electric shift control module	Electric shift selector	Continuity
1	E131	34	M2	2	Existed
2	35	14
3	36	3
4	37	15
5	44	4
6	45	16
7	39	5
8	40	17

Electric shift sensor	Electric shift control module	―	Continuity
1	E131	34	Ground	Not existed
2	35
3	36
4	37
5	44
6	45
7	39
8	40

Check the continuity between the electric shift control module harness connector terminals.

Electric shift sensor	Electric shift control module		Electric shift control module		Continuity
Electric shift sensor	Connector	Terminal	Connector	Terminal	Continuity
1	E131	34	E131	Except 34	Not existed
2		35		Except 35
3		36		Except 36
4		37		Except 37
5		44		Except 44
6		45		Except 45
7		39		Except 39
8		40		Except 40

Is the inspection results normal?

Repair or replace damaged parts.

5.REPLACE ELECTRIC SHIFT SELECTOR

Is DTC detected?

Replace the electric shift control module. Refer to Removal and Installation

INSPECTION END