[Previous][Next]
M.U.T.-III SE Function
 
 
APPLICATION ITEMS
M.U.T.-III SE can perform the following diagnosis modes via CAN communication and the combination meter.
Diagnosis modeDescription
Self Diagnostic ResultDisplay DTC which combination meter memorizes.
Data ListDisplays combination meter input/output data in real time.
Work SupportDisplays combination meter part number.
Warning HistoryLighting history of the warning light and indicator light can be checked.
Configuration
  • The vehicle specification that is written in combination meter can be displayed or stored
  • The vehicle specification can be written when combination meter is replaced
 
 
SELF DIAG RESULT
Refer to DTC Index.
 
 
Freeze frame data (FFD)
When DTC is detected, the following vehicle condition is recorded and it is displayed on the M.U.T.-III SE screen.
Item nameDisplay item
ODO/TRIP METERRecords an odometer value when DTC is detected.
  • Current odometer value is shown when the displayed DTC means a present malfunction.
  • Odometer value of the time of returning to normal is shown when the displayed DTC means a past malfunction.
DTC countRecords the number of times DTC was detected.
 
 
DATA MONITOR
noteThe following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to M.U.T.-III SE display items.
 
 
Display Item List
X: Applicable
Display item [Unit]MAIN
SIGNALS
Description
SPEED METER
[km/h]
XValue of vehicle speed signal received from ECM via CAN communication.
note655.35 is displayed when the malfunction signal is received.
SPEED OUTPUT
[km/h]
XVehicle speed signal value transmitted to other units via CAN communication.
note655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
[km/h]
Odometer signal received from ABS actuator and electric unit (control unit) via CAN communication.
TACHO METER
[rpm]
XValue of the engine speed signal received from ECM via CAN communication.
note8191.875 is displayed when the malfunction signal is received.
FUEL METER
[L]
XFuel level indicated on combination meter.
W TEMP METER
[°C]
XValue of engine coolant temperature signal is received from ECM via CAN communication.
note215 is displayed when the malfunction signal is input.
ABS W/L
[On/Off]
Status of ABS warning light detected from ABS warning light signal is received from ABS actuator and electric unit (control unit) via CAN communication.
ASC/TCS IND
[On/Off]
Status of ASC OFF indicator light detected from ASC OFF indicator light signal is received from ABS actuator and electric unit (control unit) via CAN communication.
SLIP IND
[On/Off]
Status of ASC warning light detected from ASC warning light signal received from ABS actuator and electric unit (control unit) via CAN communication.
BRAKE W/L
[On/Off]
Status of brake warning light detected from brake warning light signal is received from ABS actuator and electric unit (control unit) via CAN communication and brake fluid level switch signal from brake fluid level switch.
noteDisplays “Off” if the brake warning light is illuminated when the valve check starts, the parking brake switch is turned ON or the brake fluid level switch is turned ON.
E-PKB warning light
[On/Off]
Status of electric parking brake warning light detected from electric parking brake warning light signal from electric parking brake control module via CAN communication.
HI-BEAM IND
[On/Off]
Status of high beam indicator light detected from high beam status signal is received from BCM via CAN communication.
TURN IND
[On/Off]
Status of turn signal indicator light detected from turn indicator signal is received from BCM via CAN communication.
FR FOG IND
[On/Off]
Status of front fog light indicator light detected from front fog light status signal is received from BCM via CAN communication.
RR FOG IND
[Off]
noteThis item is displayed, but cannot be monitored.
LIGHT IND
[On/Off]
Status of position light indicator light detected from position light status signal is received from BCM via CAN communication.
OIL W/L
[On/Off]
Status of engine oil pressure warning detected from engine oil pressure warning light signal is received from ECM via CAN communication.
MIL
[On/Off]
Status of malfunction indicator light detected from malfunctioning indicator light signal is received from ECM via CAN communication.
BA W/L
[On/Off]
Status of AEB warning light judged from AEB warning light signal received from ADAS control unit via CAN communication.
WASHER W/L
[On/Off]
Status of low washer fluid warning judged from washer level switch input to combination meter.
AIR PRES W/L
[On/Off]
Status of low tire pressure warning light judged from low tire pressure light signal received from BCM via CAN communication.
EPS W/L
[On/Off]
Status of electric power steering warning light detected from electric power steering warning light signal is received from EPS control unit via CAN communication.
DDS W/L
[Off]
noteThis item is displayed, but cannot be monitored.
CHAGE W/L
[On/Off]
Status of 12V battery charge warning light judged from battery warning request signal received from ECM or IPDM E/R via CAN communication.
E-PKB indicator
[On/Off]
Status of electric parking brake indicator light detected from electric parking brake indicator light signal from electric parking brake control module via CAN communication.
BRAKE OIL SW
[On/Off]
Status of brake fluid level switch.
PASS BUCKLE SW
[On/Off]
Status of front seat belt buckle switch (passenger side) detected from passenger seat belt buckle switch signal from air bag diagnosis sensor unit via CAN communication.
CHG CONCT DET
[Off]
noteThis item is displayed, but cannot be monitored.
DISTANCE
[km]
Value of distance to empty calculated by combination meter.
OUTSIDE TEMP
[°C]
Ambient temperature value converted from ambient sensor signal received from ambient sensor.
noteThis may not match with the temperature value indicated on the information display. (Because the information display value is a corrected value from the ambient sensor input value.)
BUZZER
[On/Off]
XBuzzer status (in the combination meter) is detected from the buzzer output signal received from each unit via CAN communication and the warning output condition of the combination meter.
STRG SW INPUT
[SW1-SW12, NOT INPUT]
Status of steering switch.
HI-BEAM ASST IND
[On/Off]
Status of high beam assist indicator light from high beam assist indicator light signal is received from BCM via CAN communication.
DIPPED BEAM IND
[Off]
noteThis item is displayed, but cannot be monitored.
Engine Off timer
noteThis item is displayed, but cannot be monitored.
Vehicle distance
noteThis item is displayed, but cannot be monitored.
EAPM status
[No spprt]
noteThis item is displayed, but cannot be monitored.
 
 
WORK SUPPORT
Function nameWork ItemDescription
ECU InformationThe combination meter part number is displayed.
 
 
ECU IDENTIFICATION
The combination meter part number is displayed.
 
 
WARNING HISTORY
  • Stores histories when warning/indicator light is turned on.
  • “WARNING HISTORY” indicates the “TIME” when the warning/ indicator light is turned on.
  • The “TIME” above is:
    • 0: The condition that the warning/indicator light has been turned on 1 or more times after starting the engine and waiting for 30 seconds.
    • 1 - 39: The number of times the engine was restarted after the 0 condition.
    • NO WARNING HISTORY: Stores NO (0) turning on history of warning/indicator light.
note
  • WARNING HISTORY is not stored for approximately 30 seconds after the engine starts.
  • Brake warning light does not store any history when the parking brake is applied or the brake fluid level gets low.
 
 
Display Item
Display itemDescription
ABS W/LLighting history of ABS warning light.
ASC/TCS INDLighting history of ASC OFF indicator light.
SLIP INDLighting history of ASC warning light.
BRAKE W/LLighting history of brake warning light.
OIL W/LLighting history of engine oil pressure warning light.
C-ENG W/LLighting history of malfunction indicator light (MIL).
BA W/LLighting history of AEB warning light.
AIR PRES W/LLighting history of low tire pressure warning light.
EPS W/LLighting history of electric power steering warning light.
CHAGE W/LLighting history of 12V battery charge warning light.
noteIn items displayed on the M.U.T.-III SE screen, only those listed in the above table are used.
 
 
CONFIGURATION
Configuration includes the following functions.
FunctionDescription
Read/Write ConfigurationBefore replacing ECUAllows the reading of vehicle specification written in combination meter to store the specification in M.U.T.-III SE.
After replacing ECUAllows the writing of the vehicle information stored in M.U.T.-III SE into the combination meter.
Manual ConfigurationAllows the writing of the vehicle specification into the combination meter by hand.