[Previous][Next]
DTC Description
 
 
DTC DETECTION LOGIC
DTC No.M.U.T.-III SE screen terms
(Trouble diagnosis content)
DTC detection condition
C106507RR LH wheel sensor
(Rear left wheel sensor)
1Diagnosis condition
  • When ignition switch is ON.
  • When rear left wheel sensor power supply voltage is normal.
  • When the vehicle speed is 10 km/h (6.2 MPH) – 60 km/h (37 MPH).
Signal (terminal)Rear left wheel sensor signal
ThresholdWhen distance between rear left wheel sensor and rear left wheel sensor rotor is large.
Diagnosis delay time1 – 60 seconds or more
2Diagnosis condition
  • When ignition switch is ON.
  • When rear left wheel sensor power supply voltage is normal.
  • When the vehicle speed is 10 km/h (6.2 MPH) – 60 km/h (37 MPH).
Signal (terminal)Rear left wheel sensor signal
ThresholdWhen installation of rear left wheel sensor or rear left wheel sensor rotor is not normal.
Diagnosis delay time1 – 60 seconds or more
3Diagnosis condition
  • When ignition switch is ON.
  • When rear left wheel sensor power supply voltage is normal.
  • When the vehicle speed is 10 km/h (6.2 MPH) – 60 km/h (37 MPH).
Signal (terminal)Rear left wheel sensor signal
ThresholdWhen there is contamination on or damage to the rear left wheel sensor or rear left sensor rotor.
Diagnosis delay time1 – 60 seconds or more
 
 
POSSIBLE CAUSE
noteConfirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
PAST DTCCRNT DTC
  • Harness or connector
  • Rear left wheel sensor
  • Rear left sensor rotor
  • Rear left tire size
  • ABS actuator and electric unit (control unit) power supply system
  • Fuse
  • Fusible link
  • 12V battery
  • Vehicle was not driven after previous repair
  • Harness or connector
  • Rear left wheel sensor
  • Rear left sensor rotor
  • Rear left tire size
  • ABS actuator and electric unit (control unit)
  • ABS actuator and electric unit (control unit) power supply system
  • Fuse
  • Fusible link
  • 12V battery
 
 
FAIL-SAFE
The following functions are suspended.
  • ASC function
  • TCS function
  • ABS function
  • EBD function
  • Brake limited slip differential (BLSD) function
  • Brake assist function
  • Brake force distribution function
  • hill start assist function
  • Electric parking brake function
  • Hill Decent Control funciton
 
 
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.
: .
 
2.CHECK DTC DETECTION
With M.U.T.-III SE
  1. Start the engine.
  2. Drive the vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.
  3. Stop the vehicle.
  4. Ignition switch OFF (Auto ACC function OFF).
  5. Start the engine.
    noteWait at least 10 seconds after start the engine.
  6. Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
-1“Active DTC” is displayed: Refer to Diagnosis Procedure.
-2“Stored DTC” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
-1To check malfunction symptom before repair: Refer to Intermittent IncidentIntermittent Incident.
-2Confirmation after repair: INSPECTION END